iFlight Cidora SL5 V2 HD w/ DJI Air Unit (BNF) (4S or 6S)

Combining DJI’s digital FPV system with iFlight innovative drones gives you an incredible HD pilot experience!

The Cidora SL5 V2.1 HD w/ DJI Air Unit BNF features the amazing new DJI FPV system, this quad makes flying FPV truly breath-taking. With the 720p video shown at 120fps through the goggles, DJI has set the bar at a new high for clarity and image quality in an FPV system. This frame offers a squashed X layout for maximum control, equipped SucceX-D F7(50A 4-in-1 ESC) stack and popular XING motors. Everything you just need to bind and fly!

Different power version (4S and 6S available) to fit most pilots requirements.

Features

• Everything you need to bind and fly!
• Optimized weight distribution: DJI unit and Stack centered
• Equipped with SucceX-D F7(SucceX 50A BLHeli32 4-in-1 ESC) Stack
• Equipped with the DJI FPV Air Unit -Bind and Fly
• Buttery-smooth 720p 120fps FPV feed
• Pre-tuned with smooth freestyle settings
• Full 3K Carbon Fiber airframe with chamfered arms
• Equipped with XING 2207 motors （6S 1800kv / 4S 2450kv)
• Weight: 445.4g without battery and GoPro mount
• LED illuminated Logo

Factory Setup Files, Pinouts and Wiring Guides

Iflight have provided all of their factory dumps, along with frame assembly, and electronics wiring guides on their google drive folder

• Cidora SL5 HD betaflight dumps
• Succex 50A ESC wiring guide and pinout
• Succex-D F7 FC wiring guide and pinout

Nazgul5 HD Quad BNF Included Components and Parts

• 1x Cidora SL5 V2.1 4S 6S FPV Drone – BNF
• 1x DJI FPV camera
• 1x DJI FPV Air Unit Module
• 2x DJI LHCP RP-SMA 5.8g FPV antenna
• 2 sets x Nazgul 5140 propellers (Set of 4 – Color may vary)
• 1 x 20*250mm battery strap (Color May Vary)
• 1x 20*200mm battery strap (Color May Vary)
• 1x GoPro TPU bottom stand incl. lock screw

NOTE: The GoPro9 camera and TPU camera mount are not included.

Suggested Extra Parts

• DJI HD FPV Goggles
• DJI Remote Controller
• 4s 1500mAh Lipo or 6S 1100mAh

The DJI Remote Controller is recommended for beginners since you won’t need to set up another receiver, but it is also optional in this BNF drone because it is NOT required in order to use the FPV system. If you don’t choose to use the DJI Remote Controller, you can choose a receiver option for your transmitter. and then bind to your own radio as usual.

Detailed Specs

FC// SucceX-D F7 V2.1 TwinG

– MCU: 216MHz STM32F722

– Gyro：2x ICM20689

– Baro: YES

– Blackbox：32MB

– Betaflight OSD: YES

– BEC: 5V 2.5A / 9V 2.5A

– Current sensor scale:  100

– Inverter for SBUS input (UART2-RX)

– Smartaudio & Tramp VTX protocol supported

– Beeper pad : Yes

– RSSI input pad: No

– UARTs：5

– Motor outputs: 8

– 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)

– 6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V)

– BLHeli32 Telemetry：RX5

– Input voltage：recommended 2-6S, MAX 8S

– Firmware Target:   IFLIGHT_F722_TWING

– Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm

– Dimensions:   36*36mm

– Weight: 7.5g

– USB type-C

ESC // SucceX 50A 2-6S BLHeli32 4-in-1 ESC

– Dimension: 43*39mm

– Mounting Holes: 30.5*30.5mm/Φ3mm

– Weight:14.4g

– Volts input: 2-6S

– STM32F051 MCU, 48Mhz Runs BLHELI 32.X Firmware

– Current sensor: Yes

-Telemetry：Supported

– BEC: No

– Supports: DShot DShot150/300/600/1200/MultiShot/ OneShot etc.

– Target: iFlight-BL32-4IN1