Zeez Design F7 2020 Stack + 45A 3-6S BlHeli32 4-in-1 ESC

The Zeez Design 2020 Stack comes with the Zeez F7 2020 FC and 45A 3-6S BlHeli32 4-in-1 ESC, to help give your multirotor full power! This stack brings lots of power in a full package. The Zeez  2020 stack features an OSD chip Onboard, 6 available UARTS, STM32F722 MCU (Support Betaflight, INav, Emuflight), BlHeli32 Firmware (support Dshot150/ Dhsot300 /Dshot600/ProShot 1000) and still compatible with all older analog protocol (OneShot42, OneShot125, Multishot).

Specifications

• Weight (including FC+ESC+ 8X Standoff + 4X Nut + 8 Pin connector) : 19.9gr
• Dimensions: ( L X W X H) : 41.6mm X 33.6mm X 19.6 mm

Zeez F7 2020 Specifications

• Mounting Holes 20×20
• Direct solder connection and board space for TBS Nano RX and TBS Unify Pro32 Nano providing the ultimate in clean stack installation.
• Up to 8S input (max 36V)
• 5V BEC up to 3A continuous
• STM32F722 MCU (Support Betaflight, INav, Emuflight)
• MPU6000 Gyro/ACC for smooth performance
• 128MB Onboard flash
• OSD chip Onboard
• 6 available UARTS
• VTX switch to control the ON/OFF of the VTX
• directly from your transmitter (control via Betaflight with USER1 mode)
• LC Filter for 5V VTX and Camera
• USB Type C connector
• Onboard RGB LED distribution for clean wiring
• to the LED on the arm of the quad.
• 8 Onboard RBG LED (compliant with FAI Rules)
• Logic Side and USB current protection

Zeez 4-in-1 45A 2020 ESC

• Mounting Holes 20×20
• 3S to 6S input
• Constant Current: 45A
• Peak Current: 55A
• STM32L4 MCU (ARM Cortex M4, 80MHz frequency)
• BlHeli32 Firmware (support Dshot150/ Dhsot300 /Dshot600/ProShot 1000) and still compatible with all older analog protocol (OneShot42, OneShot125, Multishot)
• 8 Pin JST connector and 8 Pin solder pads
• Holes for Aluminum Low ESR capacitor (included 35V 470uF Low ESR capacitor and a spare capacitor)
• Onboard analog current sensor (Betaflight Scale: 200)
• ESC telemetry to read RPM and ESC temperature
• Compatible with Bidirectional Dshot out of the box

Includes

• 1 x Zeez F7 2020 Flight Controller
• 1 x Zeez ESC 4in1 45A 2020
• 8 x Aluminum Standoff
• 4 x Aluminum Nut
• 1 x ESC to Flight Controller 8 Pin to 8 Pin JST SH 1.00mm connector
• 1 x ESC to Flight Controller 8 Pin to Free wires (with JST SH crimp) JST SH 1.00mm connector
• 1 x ESC to Flight Controller 8 Pin to Servo Connector JST SH 1.00mm connector
• 1 x JST SH 8 Pin Plastic Housing
• 1 x JST SH 10 Pin Plastic Housing
• 2 x 470uF 35V Low ESR Capacitor
• 1 x XT60 with 12AWG Silicon Cable for battery connection
• 2 x 2.00mm Header Pin for VTX connection
• 2 x 2.54mm Header Pin for Receiver connection
• 4 x Spare M3 rubber anti-vibration for Flight Controller or ESC